|
 
Automotive
Reset Selection
NZ$40.00*
  • ATC /ATO fuse extender keeps fuse in circuit while testing
  • Allows easy current (clamp) measurement.
  • Simply move fuse to extension, plug extension in where fuse was and clamp to measure
NZ$536.00*
PicoBNC+ 60A AC/DC current clamp
  • For measuring currents between 10 mA and 60 A
  • Display current waveforms for fuel injectors and fuel pumps.
  • Improved performance and diagnostic accuracy
NZ$506.00*
TA167 - 200A/2000A AC/DC current clamp
  • Measure high compression diesel and petrol starter currents
  • 0 to 200/2000 Amps DC & AC pk (to 20kHz)
  • Easy push-button Zero Set
NZ$536.00*
PicoBNC+ 2000 A AC/DC current clamp
  • Allows you to measure up to 2000 amps without cutting, or disconnecting or stripping wires
  • No batteries required
  • Ranging is carried out automatically with no user switching required
NZ$372.00*
PicoBNC+ COP and signal probe
  • Displays scope patterns of the secondary, faster than scoping the primary
  • Flexible design allows for easier access to hard-to-reach components
  • No batteries required
NZ$344.00*
Coil-On-Plug (COP) Ignition Probe & Cable
  • Display scope patterns of the secondary, faster than scoping the primary
  • Suitable for use on most COP & conventional ignition systems
  • Find misfires fast
NZ$737.00*
Mixmaster 12 Cylinder Auto Signal Mixer
  • View ignition parades of up to 12 cylinders
  • Display 2 engine banks of up to 6 cylinders each
  • Supplied with 4 secondary ignition leads, extra leads available
NZ$49.00*
BNC to BNC Cable with Earth Clamp
  • For use with the Coil-On-Plug Ignition Probe
  • Length: 3 metres
NZ$194.00*
Mixmaster Secondary Ignition Pickups
  • A set of 4 secondary ignition, leads, each 40cm long
  • Combine with Mixmaster & 4-channel scope leads to display 12 channel parade
  • Get the most from your Mixmaster
NZ$107.00*
Secondary Ignition Pickup
  • View secondary ignition waveforms directly on-screen with an Automotive Oscilloscope
  • Shielded 1.8m lead. Clips over plug lead or COP extension
  • For use with conventional ignition systems and most HEI and DIS systems
NZ$116.00*
PicoBNC+ secondary ignition pickup
  • View secondary ignition waveforms directly on-screen with an Automotive Oscilloscope
  • Shielded 1.8m lead. Clips over plug lead or COP extension
  • This lead is fitted with a PicoBNC+ interface
NZ$81.00*
  • Single extension lead
  • Clip Pico secondary ignition lead over extension to see HT waveform
  • Simply fit between coil pack & plugs
NZ$162.00*
PicoBNC+ Temperature probe (wide-range linear)
  • Measures in the range -40° to 125°
  • Enclosed in a 5mm stainless steel housing to provide contact and airflow measurement.
  • Available only for PicoBNC+
NZ$56.00*
Keyless entry carrier signal detector
  • Detect the presence of the keyless entry carrier frequency
  • In the range of 125-140 kHz
  • 3m long lead
NZ$56.00*
Ultrasonic parking sensor detector
  • Prove the correct operation of each of the ultrasonic parking sensors
  • Directly showing the strength of the signal from a given sensor
  • 2m long lead
NZ$480.00*
  • For working on larger vehicles
  • 5m long BNC to 4mm cable, with 2.5m fixed ground
  • Insulated BNC connector, shrouded 4mm plugs
NZ$354.00*
  • Set of four colours, removable and fixed ground
  • Leads match scope trace colours
  • 3m insulated BNC to stackable shrouded banana plugs
NZ$7.00*
MI168 S-Hook
  • Makes it easy to keep test leads tidy in the engine bay
  • Hang PicoScope up by its boot loop
  • 100 mm long, plastic coated with rubber caps
NZ$28.00*
  • Insulated BNC to BNC cable, measuring 50 cm (0.5 m) in length.
NZ$107.00*
  • Fully shielded for the complete length of the signal cable
  • 3 m leads come with fixed 1.5 m ground extensions
  • Shrouded/stacking banana plugs
NZ$134.00*
  • Fully shielded for the complete length of the signal cable
  • 5 m leads come with fixed 1.5m ground extensions
  • Shrouded/stacking banana plugs
NZ$21.00*
  • Fully insulated with a 4 mm socket in the handle
  • Easy connection to Pico Premium test lead
  • Wide 30 mm opening jaw
NZ$5.00*
  • Fully insulated with 4mm socket in the handle
  • Toothed grip offers good contact on fine wire
  • Easy connection to Pico Premium Test Leads
NZ$5.00*
  • Fits all our BNC to 4 mm Pico Premium Test Leads
  • Plier type clips designed to grab and hold the vehicle battery terminals
NZ$116.00*
Red/Black Pair of Insulation Piercing Clips
  • Provides the exact pressure needed to pierce the insulation of a wide range of wires
  • Rotating banana jacks prevent test lead twisting
  • Keeps the oscilloscope in-circuit while the wire is pierced
NZ$79.00*
TA008 Acupuncture Back Pinning Probe Set
  • Back pinning probe set
  • Fit onto 4mm banana plugs, fine tips slide easily past connector seals
  • 7 complete acupuncture probes, 3 probe sizes, replacement screws & needles
NZ$7.00*
  • Designed for back-probing under the insulation
  • Flexible mid-section improves access to difficult terminals
  • Fits easily onto Pico Premium Test Leads
NZ$10.00*
  • When a quick non-clip-on connection is required
  • Pushes easily onto a Pico Premium Test Lead
  • 4mm socket, length 115mm. Also available in black
NZ$5.00*
  • Adapts 4mm shrouded plug to unshrouded plug
  • Allows test lead connection into any breakout box
  • Quick push-on connection
NZ$517.00*
PicoScope professional breakout lead set
  • 14 sets with flat blade connectors in different sizes
  • 4 sets with round pins in different sizes
  • 1 set with square pins in one size
NZ$206.00*
  • Connect into any vehicle without specialised leads
  • Eliminates the need to own many specific breakout leads for engine diagnostics
  • Available with 0.6, 1.5, 2.3 & 2.8mm male & female spade connectors
NZ$60.00*
TA012 Two Pin Break Out Lead
  • Enables voltage readings from numerous 2 pin sensors in the engine compartment
  • Separate access to individual wires allows easy current measurement with clamps
  • Simultaneously display both injector current and voltage on your PicoScope
NZ$499.00*
PP619 CAN-Bus Test Box
  • Instantly Check Power & Ground Circuits
  • Identify Communication Link Protocols
  • Connect to PicoScope
NZ$74.00*
Foam Tray for CAN-Bus Test Box
  • Protect your tester and its cable in this foam storage tray
NZ$877.00*
TA014 FirstLook Engine Diagnostic Sensor
  • Fast & accurate automotive diagnosis from tail pipe
  • Diagnose burnt valves, bad injectors & other problems without major disassembly
  • Includes vacuum line adaptor & connector cable
NZ$314.00*
MEMS Accelerometer
  • Used in conjuction with the NVH interface
  • Detects motion across the X,Y and Z axes
NZ$86.00*
Mounting magnet for accelerometer
  • Mounting magnet for the TA143 Accelerometer.
NZ$157.00*
Standard Pico Microphone
  • The standard Pico microphone for use with Pico's NVH Interface
NZ$162.00*
Sensor Extension Cable 3 m
  • A black 3 m extension cable for Pico's NVH interface
NZ$118.00*
TA197 10:1 Attenuator
  • Perform quick and accurate ignition waveform analysis of many automotive systems
  • Allows voltages of up to 400 V to be measured
  • Increases the input impedance of the oscilloscope from 1 MΩ to 8 MΩ
NZ$30.00*
  • Connect PicoScope to PC
  • Scope power and high signal rating
  • Compatible with USB2 PCs